FAQs

FAQS

He aha nō i ka papa kuhikuhiEʻano o SPS squeegee?

SPS squeegee ua hoʻolaha i loko o ekolu nui waeʻano: 1. Traditional M-type squeegee (me kākoʻo papa). 2, FGB o Minvielle i hamoʻia. 3, LIKE unilateral kalapona puluniu hamo nui aʻe ana.

Aia i kekahi mau Ke Ana Hoʻohālike o ka laholio hapa o ka SPS squeegee?

Aia nō Ke mau ana hoʻohālike, kekahi o ka M-type laholio hoʻohana ma o ka M-'ano a me ka FGB o Minvielle i Panel, a me ka mea' ē aʻe o ka hua hoʻohui laholio hoʻohana ma o ka LIKE-kalapona puluniu (lawelawe, oi'ūheheʻe-hoʻopale, a oi wear- hoʻopale).

He aha nō ka nui hoakaka o ka M 'ano hamoʻia glue?

M Ke Ana Hoʻohālike i 9 * 50, 9 * 30, 7 * 40, 5 * 25, 5 * 20 kōkua mānoanoa e like me ka mānoanoa, a ua hiki ke i hoʻopilikino 'e like me ka Customer olelo.

He aha e na Ana o FGB o Minvielle i scraper?

Ke kahiko pale pai hana FGB o Minvielle i hamoʻia hoakaka o 9 * 50, ka lōʻihi o ka oki, e like me ka Customer olelo. Hiki e i hoʻopilikino 'e like me ka Customer olelo.

He aha e na Ana o LIKE kalapona puluniu squeegee?

Ke kahiko pale pai hana LIKE kalapona puluniu hamoʻia hoakaka 7 * 50, lōʻihi e like me ka Customer olelo. Hiki e i hoʻopilikino 'e like me ka Customer olelo.

He aha ka ka hulu waihona, a he mau manawa koi 'ia no ka lawelawe oihana?

3D: STP, XT; CAD: 2000 mana, me ke dute manawa: i loko o 5 mau lā hana

Is it possible to grind the SPS squeegee?

Ka ekolu 'ano o ka scraper hiki ke wili. M kükohu a FGB kükohu hoʻokahi i kā mākou wili dala 0.5mm (200 hei wili huila). LIKE kalapona puluniu hamo hookahi i kā mākou wili dala 0.1mm (200 hei wili huila, kalapona puluniu papa hiki no hoi e lepo). Ke squeegee mea i pono, ua hoʻohana i kekahi i ka hailona o'ūheheʻe oloko. Ka paakiki o ka pahi kaʻe mea, ua haʻahaʻa ia e hoʻowali koke. Ua lawe 24 wale hola mua wili.

Pehea e? Ac FGB o Minvielle i scraper, a LIKE kalapona puluniu scraper iʻike mau fixtures?

Ua ka FGB o Minvielle i scraper a me ka LIKE kalapona puluniu scraper i 1.2mm loa. Ka mea hiki ke hoʻouka kekahi me ka 8mm manoanoa pale, a ua hiki i.

Malama o SPS Squeegee?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.