FAQs

FAQS

He aha e nga momo matua o SPS squeegee?

whakarōpūtia SPS squeegee ki toru ngā wāhanga matua: 1. Traditional M-momo squeegee (kahore he pereti tautoko). 2, FGB kaka kōata haro. 3, muka waro AS unilateral haro kapia.

He maha ngā tauira o te wahi rapa o te squeegee SPS?

E tēnei wā e rua tauira, kotahi Ko te rapa M-momo whakamahia i roto i te M-momo me FGB awhi kaka, me te tahi atu ko te rapa PLUS whakamahia i roto i te muka AS-waro (conductive, atu whakarewa-ātete, me te ake wear- ātete).

He aha e nga ngā rahi o te momo M haro kāpia?

M tauira i 9 * 50, 9 * 30, 7 * 40, 5 * 25, 5 * 20 matamata matotoru rite ki matotoru, a taea te whakarite rite ki ngā whakaritenga kiritaki.

He aha e nga āhuatanga o FGB kaka kota?

Ko te tuku iho kaka kōata ahumahi tā mata FGB haro ngā o 9 * 50, te roa o te tapahi rite ki ngā whakaritenga kiritaki. Taea te whakarite rite ki ngā whakaritenga kiritaki.

He aha e nga āhuatanga o AS muka waro squeegee?

Te ahumahi tā mata tuku iho AS ngā muka waro hāro 7 * 50, roa rite ki ngā whakaritenga kiritaki. Taea te whakarite rite ki ngā whakaritenga kiritaki.

He aha te mea te hōputu kōnae me te whakaritenga wā e hiahiatia ana mō ngā ratonga ritenga?

3D: STP, XT; CAD: 2000 putanga, te wā ritenga: i roto i 5 ra mahi

Is it possible to grind the SPS squeegee?

Ka taea te hurihia nga momo e toru o te kota. M tauira me te tauira FGB mōrahi kotahi huri 0.5mm nui (200 mata huri wira). AS muka waro haro kotahi 0.1mm nui huri mōrahi (200 mata huri wira, Ka taea e te poari muka waro hoki hei whenua). Ko te squeegee e kua tika kua whakamahia ake kei te rota o te roto whakarewa. He iti rawa ki te kia hurihia tonu te pakeke o te mata maripi. E te reira 24 anake haora i mua i huri.

Me pēhea te ki te tāuta FGB kaka kota me AS muka waro kota ki huaki tikanga?

Rua te FGB kaka kota me te AS muka waro kota e 1.2mm matotoru. Ka taea te tāuta ratou ki te papa matotoru 8mm, e nehenehe ia tatou ia whakarato.

Whakatikatika o SPS squeegee?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.