FAQs

FAQS

O a ni ituaiga autu o squeegee SPS?

ua faavasegaina squeegee SPS i vaega tetele e tolu: 1. Traditional squeegee M-ituaiga (e aunoa ma ipu lagolago). 2, fufuluina fau tioata FGB. 3, AS alava carbon toatasi fufuluina pulu.

E tele ni faataitaiga o le paʻu vaega o le squeegee SPS?

O le taimi nei faataitaiga e lua, o le tasi o le paʻu M-ituaiga faaaogaina i le M-ituaiga ma FGB panels fau tioata, ma le isi o le paʻu Plus faaaogaina i le alava AS-carbon (conductive, e sili atu mafai ona totogi aitalafu-e tetee, ma e sili wear- tetee).

A le tele auiliili o le ituaiga fufuluina kelu M?

faataitaiga M maua 9 * 50, 9 * 30, 7 * 40, 5 * 25, 5 * 20 mafiafia tumutumu e tusa ma mafiafia, ma e mafai ona patino e tusa ai ma manaoga o tagata e faaaogāina auaunaga.

O a ni fua o FGB scraper fau tioata?

Le alamanuia lomitusi masani lau fau tioata FGB fufuluina auiliili o 9 * 50, o le umi o le tipiina e tusa ai ma manaoga o tagata e faaaogāina auaunaga. E mafai ona patino e tusa ai ma manaoga o tagata e faaaogāina auaunaga.

O a ni fua o le AS squeegee alava carbon?

Le alamanuia lomitusi masani lau AS auiliili fufuluina alava carbon 7 * 50, umi e tusa ai ma manaoga o tagata e faaaogāina auaunaga. E mafai ona patino e tusa ai ma manaoga o tagata e faaaogāina auaunaga.

O le a le faila faatulagaga ma customization taimi e manaomia mo auaunaga masani?

3D: STP, XT; CAD: 2000 lomiga, taimi masani: totonu o le 5 aso faigaluega

Is it possible to grind the SPS squeegee?

O ituaiga e tolu o scraper mafai ona eleele. M faataitaiga ma FGB faataitaiga tasi maualuga olo aofaiga 0.5mm (200 mesh uili olo). AS carbon alava fufuluina tasi 0.1mm aofaiga olo maualuga (200 mesh olo uili, foi ona eleele e mafai ona laupapa alava carbon). O le squeegee ua faatoa faaaoga i luga o loo i ai le tele o le mafai ona totogi aitalafu i totonu. e maualalo tele le maaa o le pito naifi ia ma tuua loa. E manaomia ai na o le 24 itula ao lumanai olo.

Le auala e faapipii FGB fau tioata scraper ma AS scraper alava carbon i totoga e masani ai?

Uma le scraper fau tioata FGB ma le scraper alava carbon AS e 1.2mm mafiafia. E mafai ona faapipii i se pad mafiafia 8mm, lea e mafai ona tatou tuuina atu.

Tausiga o SPS Squeegee?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.