FAQs

FAQS

ke mefuta e ka sehloohong ea SPS squeegee eng?

SPS squeegee e classified ka lihlopha tse tharo tse khōlō: 1. Traditional M-mofuta squeegee (ntle le tšehetso poleiti). 2, FGB fiberglass fala. 3, AS unilateral k'habone faeba fala kauwen.

Ho na le dikai 'maloa ea karolo e rabara ea SPS squeegee?

Ho na le hona joale dikai tse peli, e 'ngoe ke M-mofuta rabara sebelisitsoe ka M-mofuta le FGB fiberglass diphanele,' me e mong ke PLUS rabara sebelisitsoe ka JOALOKAHA-k'habone faeba (conductive, ho feta solvent manganga, 'me ho feta wear- manganga).

ke boholo tobileng tsa M mofuta fala sekhomaretsi seo?

M dikai na 9 * 50, 9 * 30, 7 * 40, 5 * 25, 5 * 20 keletso botenya ho latela botenya, 'me ka ho customized ho latela ditlhoko moreki.

ke litekanyo tsa FGB fiberglass eyelet eng?

Ea neano indasteri skrine oa khatiso FGB fiberglass fala tobileng ea 9 * 50, bolelele ba seha ho latela ditlhoko moreki. Ka customized ho latela ditlhoko moreki.

ke litekanyo tsa JOALOKAHA k'habone faeba squeegee eng?

Ea neano skrine indasteri ea khatiso JOALOKAHA k'habone faeba fala tobileng 7 * 50, bolelele ho latela ditlhoko moreki. Ka customized ho latela ditlhoko moreki.

ke faele thalong le declaration nako hlokehang bakeng sa ditshebeletso tloaelo efe?

3D: STP, XT; CAD: 2000 tlhahiso, nako le tloaelo: hara matsatsi a 5 ho sebetsa

Is it possible to grind the SPS squeegee?

The mefuta e meraro ea eyelet ka fatše. M ea mohlala le FGB ea mohlala le 'ngoe palo e kahodimodimo ho sila chelete 0.5mm (200 letlooeng sila lebili). JOALOKAHA k'habone faeba fala le 'ngoe lebetsoeng le sila chelete 0.1mm (200 letlooeng sila lebili, carbon faeba boto ka boela ba fatše). The squeegee hore e feela e sebediswa ho fihlela e na le e ngata ka hare solvent. The thatafala ea thipa bohale ke e tlase haholo ho di fatše hang-hang. Ho nka lihora tse 24 feela pele ho sila.

Mokhoa oa ho kenya FGB fiberglass eyelet le JOALOKAHA k'habone faeba eyelet ka lihlopha tloaelehileng?

Ka bobeli FGB fiberglass eyelet le JOALOKAHA k'habone faeba eyelet ke 1.2mm teteaneng. Ba ka hlomamisa ka 8mm sebaka tenya, eo re neng re ka fana ka.

Boloka SPS Squeegee?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.