FAQs

FAQS

SPS gelberi asosiy turlari qanday?

(Qo'llab-quvvatlash plitalari holda) 1. An'anaviy M-turi squeegee: SPS squeegee uchta asosiy toifaga tasniflanadi. 2, FGB shisha tolali qirib yurish. 3, AS tomonlama uglerod tolasi saqich qirib yurish.

SPS gelberi rezina qismi bir necha modellari mavjud?

U erda ikki modellar bir M-turi va FGB shisha tolali panellari ishlatiladigan M-turi rezina bo'lib, ayni paytda, va boshqa (AS-uglerod tolasi ishlatiladi PLUS rezina bo'lgan Supero'tkazuvchilar, yana-Hal qiluvchi, chidamli, va yana wear- chidamli).

elim qirib yurish M turi kattaligi xususiyatlari qanday?

M modellari * 50 9, * 30 9, * 40 7, * 25 5, qalinligi ko'ra 5 * 20 Maslahat qalinligini bor, va mijoz talablariga muvofiq tayyorlangan bo'lishi mumkin.

FGB shisha tolali skreper o'lchamlari nima?

9 * 50 xususiyatlarini qirib yurish an'anaviy ekran poligrafiya sanoati FGB shisha tolali, mijoz talablariga binoan kesish uzunligi. mijoz talablariga muvofiq tayyorlangan bo'lishi mumkin.

uglerod tolasi gelberi AS registri nima?

mijoz talablariga ko'ra uglerod tolasi oldirish, texnik 7 * 50, uzunligi kabi an'anaviy ekran poligrafiya sanoati. mijoz talablariga muvofiq tayyorlangan bo'lishi mumkin.

Bozhxona xizmatlari uchun zarur fayl formati va xususiylashtirish vaqt nima?

3D: STP, XT; SAPR: 2000 versiyasi, Custom vaqti: 5 ish kuni ichida

Is it possible to grind the SPS squeegee?

skreper uch turdagi maydalab mumkin. M modeli va FGB model bitta maksimal silliqlash miqdori 0.5mm (200 mash silliqlash g'ildirak). uglerod tolasi bitta maksimal silliqlash miqdori 0.1mm qirib yurish AS (g'ildirakka silliqlash 200 mash, uglerod tolasi kengashi ham zamin bo'lishi mumkin). faqat yuqoriga ishlatilgan squeegee Hal qiluvchi, ichki bir poda o'z ichiga oladi. pichoq chetiga qattiqligi darhol maydalab uchun juda ham past bo'ladi. Bu silliqlash oldin faqat 24 soat davom etadi.

Qanday FGB fiberglass kazıyıcı va an'anaviy ustunlariga ichiga uglerod tolasi raspa AS o'rnatish uchun?

FGB fiberglass Pulni va AS uglerod tolasi Pulni ikkalasi qalin 1.2mm bo'lgan. Ular biz bilan ta'minlash mumkin, 8mm qalin pad bilan o'rnatish mumkin.

SPS squeegee ta`minlash?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.