FAQs

FAQS

Ohun ti o wa ni akọkọ orisi ti SPS squeegee?

SPS squeegee ti wa ni classified sinu meta pataki ẹka: 1. Ibile M-Iru squeegee (lai support awo). 2, FGB gilaasi haruna. 3, AS ẹsẹ erogba okun haruna gomu.

Nibẹ ni o wa ni ọpọlọpọ awọn si dede ti awọn roba apa ti awọn SPS squeegee?

Nibẹ ni o wa Lọwọlọwọ meji si dede, ọkan ni M-iru roba lo ninu awọn M-iru ati FGB gilaasi paneli, ati awọn miiran ni awọn Plus roba lo ninu awọn AS-erogba okun (conductive, diẹ epo-sooro, ati siwaju sii wear- sooro).

Ohun ti o wa awọn iwọn pato ti awọn M iru haruna pọ?

M dede ni 9 * 50, 9 * 30, 7 * 40, 5 * 25, 5 * 20 sample sisanra gẹgẹ sisanra, ati ki o le wa ni ti adani gẹgẹ bi onibara awọn ibeere.

Ohun ti o wa awọn mefa ti FGB gilaasi scraper?

Awọn ibile iboju titẹ sita ile ise FGB gilaasi haruna pato ti 9 * 50, awọn ipari ti gige gẹgẹ bi onibara awọn ibeere. Le ti wa ni ti adani gẹgẹ bi onibara awọn ibeere.

Ohun ti o wa awọn mefa ti AS erogba okun squeegee?

Awọn ibile iboju titẹ sita ile ise AS erogba okun haruna ni pato 7 * 50, ipari gẹgẹ bi onibara awọn ibeere. Le ti wa ni ti adani gẹgẹ bi onibara awọn ibeere.

Ohun ti o jẹ awọn faili kika ati isọdi akoko ti a beere fun aṣa iṣẹ?

3D: STP, XT; CAD: 2000 version, aṣa akoko: laarin 5 ṣiṣẹ ọjọ

Is it possible to grind the SPS squeegee?

Awọn mẹta orisi ti scraper le ti wa ni ilẹ. M awoṣe ki o si FGB awoṣe nikan ti o pọju lilọ iye 0.5mm (200 apapo lilọ kẹkẹ). AS erogba okun haruna nikan o pọju lilọ iye 0.1mm (200 apapo lilọ kẹkẹ, erogba okun ọkọ tun le jẹ ilẹ). Awọn squeegee ti o ti o kan ti a ti lo soke ni a pupo ti epo inu. Awọn líle ti awọn ọbẹ eti jẹ ju kekere lati wa ni ilẹ lẹsẹkẹsẹ. O gba to nikan 24 wakati ṣaaju ki o to lilọ.

Bi o si fi FGB gilaasi scraper ati AS erogba okun scraper sinu mora amuse?

Mejeji awọn FGB gilaasi scraper ati awọn AS erogba okun scraper ni o wa 1.2mm nipọn. Won le wa ni sori ẹrọ pẹlu ohun 8mm nipọn pad, eyi ti a le pese.

Itọju SPS squeegee?

The squeegee is printed for a long time, and the solvent easily erodes the squeegee blade. The hardness and wear resistance of the squeegee are reduced. Therefore, after the squeegee has been printed for a long time, it needs to be cleaned, and after being left for 12-24 hours, it is used or ground again. If stored in a low-temperature environment, soak it in 30°C warm water for 10 minutes before use. Dry it with a cloth and use it. When the squeegee is left for a long time, it is forbidden to touch the other side of the squeegee to prevent the squeegee from deforming.